The proper shipping name Paint related material, corrosive, flammable may be used for consignments of packages containing Paint, corrosive, flammable and Paint related material, corrosive, flammable in the same package; c. The proper shipping name Paint related material, flammable, corrosive may be used for consignments of packages containing Paint, flammable, corrosive and Paint related material, flammable, corrosive in the same package; and. In addition, there are over 300 numeric codes provisions. 422 When labelling is required, the label to be used must be the label shown in 172.447. iv. TP19 The calculated wall thickness must be increased by 3 mm at the time of construction. 160 This entry applies to safety devices for vehicles, vessels or aircraft, e.g. See UN1210, UN1263, UN1266, UN3066, UN3469, and UN3470. B33 MC 300, MC 301, MC 302, MC 303, MC 305, MC 306, and DOT 406 cargo tanks equipped with a 1 psig normal vent used to transport gasoline must conform to Table I of this Special Provision. However, button cell batteries installed in equipment (including circuit boards) need not be considered; and, c. The shipping paper must indicate UN 3091 Lithium metal batteries packed with equipment or UN 3481 Lithium ion batteries packed with equipment, as appropriate. Thickness of stainless steel for tank shell and heads must be the greater of 7.62 mm (0.300 inch) or the thickness required for a portable tank with a design pressure at least equal to 1.5 times the vapor pressure of the hazardous material at 46 C (115 F). 328 When lithium metal or lithium ion batteries are contained in the fuel cell system, the item must be described under this entry and the appropriate entries for Lithium metal batteries contained in equipment or Lithium ion batteries contained in equipment. For other than Class 7 or the DANGEROUS . When a plus sign is assigned to mix- For continued use of approvals dated prior to January 1, 2012, see 173.308(b)(5). Net weight of contents in wooden boxes, barrels or kegs may not exceed 45 kg (99 pounds). (eg: These mixtures may be classified in Division 4.1 when tested in accordance with test series 6(c) of the UN Manual of Tests and Criteria (IBR, see 171.7 of this subchapter) and approved by the Associate Administrator. b. Lead compounds that have a solubility of 5% or less in accordance with this special provision are not subject to the requirements of this subchapter that pertain to Marine Pollutants. result, it may not include the most recent changes applied to the CFR. d. Except for transportation by aircraft, neutron radiation detectors and radiation detection systems containing such detectors transported in accordance with paragraph a of this special provision are not subject to the labeling and placarding requirements of part 172 of this subchapter. B130 When transported by motor vehicle, used diatomaceous earth filter material is not subject to any other requirements of this subchapter except for the shipping paper requirements of subpart C of part 172 of this subchapter; emergency response information as required by 172.602(a)(2) through (a)(7) of this subchapter; and the marking requirements of 172.302 of this subchapter, if the following requirements are met: a. Packagings are non-DOT specification sift-proof motor vehicles or sift-proof roll-on/roll-off bulk bins, which are covered by a tarpaulin or other equivalent means. f. Chemicals under pressure containing components forbidden for transport on both passenger and cargo aircraft in Columns (9A) and (9B) of the 172.101 Hazardous Materials Table must not be transported by air. Each IBC may not exceed a maximum net quantity of 1,000 kg: a. Column 8 Others such as copper and silver are available in trace amounts. (b) Description of codes for special provisions. IBCs of type 31A and 31N are only authorized if approved by the Associate Administrator. N77 For materials of not more than two percent active ingredients by weight, packagings need not conform to the requirements of part 178 of this subchapter, if liquid contents are absorbed in an inert material. A100 Lithium ion cells and batteries must be offered for transport at a state of charge not exceeding 30 percent of their rated capacity. B131 When transported by highway, rail, or cargo vessel, waste Paint and Paint related material (UN1263; PG II and PG III), when in plastic or metal inner packagings of not more than 26.5 L (7 gallons), are excepted from the marking requirements in 172.301(a) and (c) and the labeling requirements in 172.400(a), when further packed in the following specification and non-specification bulk outer packagings and under the following conditions: a. For example, nickel-metal hydride batteries transported by vessel in certain quantities are covered by another entry (see Batteries, nickel-metal hydride, UN3496). Table 2 defines IP Codes on the use of IBCs that are assigned to specific commodities in the 172.101 Table of this subchapter. N90 Metal packagings are not authorized. B27 Tanks must have a service pressure of 1,034 kPa (150 psig). For liquids transported under ambient conditions may be calculated using the formula: d15 and d50 are the densities (in units of mass per unit volume) of the liquid at 15 C (59 F) and 50 C (122 F), respectively. Hazardous materials necessary for the safe and proper operation of the cargo transport unit (e.g., fire extinguishing systems and air conditioning systems), must be properly secured to or installed in the cargo transport unit and are not otherwise subject to this subchapter. 22 If the hazardous material is in dispersion in organic liquid, the organic liquid must have a flash point above 50 C (122 F). The operator of an aircraft carrying hazardous materials must do all of the following EXCEPT: A. 24 Alcoholic beverages containing more than 70 percent alcohol by volume must be transported as materials in Packing Group II. (You can unsubscribe anytime), Learn More About USDOT/HazMat Transportation, generalpackaging requirements of173.24, Frequently Asked Questions Regarding the Regulations of the Resource Conservation and Recovery Act.
Your Nuclear Attack Map for 2023 - mirasafety.com (9) W codes. 125 Lactose or glucose or similar materials may be used as a phlegmatizer provided that the substance contains not less than 90%, by mass, of phlegmatizer. For transportation by aircraft, the provisions of 173.159(b)(2) apply. A13 Bulk packagings are not authorized for transportation by aircraft. TP12 This material is considered highly corrosive to steel. Wooden boxes must be completely lined with a suitable material impervious to water and nitroglycerin. 40 Polyester resin kits consist of two components: A base material (either Class 3 or Division 4.1, Packing Group II or III) and an activator (organic peroxide), each separately packed in an inner packaging. Unfortunately, the amendments to the table entries for various hazardous materials introduced new unintended errors that PHMSA is correcting in this notice. Other inorganic nitrate salts may replace part of the ammonium nitrate. A54 Irrespective of the quantity limits in Column 9B of the 172.101 table, a lithium battery, including a lithium battery packed with, or contained in, equipment that otherwise meets the applicable requirements of 173.185, may have a mass exceeding 35 kg if approved by the Associate Administrator prior to shipment. N6 Battery fluid packaged with electric storage batteries, wet or dry, must conform to the packaging provisions of 173.159 (g) or (h) of this subchapter. (7) Special Provisions (172.102) IB8, IP2, IP4 49 U.S.C. Have accident damage protection which conforms with 178.345-8 of this subchapter; c. Have a MAWP or design pressure of at least 87 psig: and. B28 Packagings must be made of stainless steel. Additionally, the offeror must notify the carrier if the tank pressure rise exceeds 3 psig over any 24-hour period. Organization and Purpose switch to drafting.ecfr.gov. A35 This includes any material which is not covered by any of the other classes but which has an anesthetic, narcotic, noxious or other similar properties such that, in the event of spillage or leakage on an aircraft, extreme annoyance or discomfort could be caused to crew members so as to prevent the correct performance of assigned duties. B46 The detachable protective housing for the loading and unloading valves of multi-unit tank car tanks must withstand tank test pressure and must be approved by the Associate Administrator. Transportation by vessel in IBCs is prohibited. 382 Packages containing toy plastic or paper caps for toy pistols described as UN0349, Articles, explosive, n.o.s. 182 Equipment containing only lithium batteries must be classified as either UN 3091 or UN 3481. There must be no hazardous effects outside the package such as disruption of the package, metal fragments or a receptacle which passes through the packaging. This content is from the eCFR and may include recent changes applied to the CFR. Lead-free Solder Figure 3: Engineer soldering a microcircuit Note, Tin here is the primary metal. c. Primary receptacles may also be further packed in specification bulk outer packagings. See Batteries, dry, sealed, n.o.s. in the 172.101 Hazardous Materials Table (HMT) of this part for transportation requirements for nickel-metal hydride batteries transported by other modes and for nickel-metal hydride button cells or nickel-metal hydride cells or batteries packed with or contained in battery-powered devices transported by vessel.
Overview of Hazardous Material Transportation Regulations 5 If this material meets the definition for a material poisonous by inhalation (see 171.8 of this subchapter), a shipping name must be selected which identifies the inhalation hazard, in Division 2.3 or Division 6.1, as appropriate. 370 This entry also applies to ammonium nitrate with not more than 0.2% combustible substances, including any organic substance calculated as carbon, to the exclusion of any added substance, that gives a positive result when tested in accordance with Test Series 2 of the UN Manual of Tests and Criteria, Part I (IBR; see 171.7 of this subchapter). It may not be used to describe articles, machinery, or apparatus for which a proper shipping name exists in the 172.101 Table. Unlined tanks must be passivated before being placed in service. A9 For combination packagings, if plastic bags are used, they must be packed in tightly closed metal receptacles before packing in outer packagings. Flexible IBCs must be sift-proof and water-resistant or must be fitted with a sift-proof and water-resistant liner.
What is Column 7 of the hazardous materials Table? 74 During transport, this material must be protected from direct sunshine and stored or kept in a cool and well-ventilated place, away from all sources of heat. TP29 A portable tank having a minimum test pressure of 1.5 bar (150.0 kPa) may be used provided the calculated test pressure is 1.5 bar or less based on the MAWP of the hazardous materials, as defined in 178.275 of this subchapter, where the test pressure is 1.5 times the MAWP. Column 7 contains special provisions associated with the hazardous material. Interpretation Response Details. c. Every installed inflation cylinder, as associated equipment of the life-saving appliance, must be packed within the protective packaging of the life raft and the life raft itself must otherwise be in compliance with 173.219. d. The serial number for each cylinder must be recorded as part of the life-saving appliance service record by the U.S. Coast Guard-approved servicing facility. N92 Notwithstanding the provisions of 173.24(g) of this subchapter, packagings shall be designed and constructed to permit the release of gas or vapor to prevent a build-up of pressure that could rupture the packagings in the event of loss of stabilization. The maximum degree of filling must not exceed the degree of filling determined by the following: tr is the maximum mean bulk temperature during transport, tf is the temperature in degrees celsius of the liquid during filling, and. Additionally, unless otherwise excepted in this subchapter, polyester resin kits must be packaged in specification combination packagings based on the performance level of the base material contained within the kit. 55 This device must be approved in accordance with 173.56 of this subchapter by the Associate Administrator. W9 When offered for transportation by water, the following Specification packagings are not authorized unless approved by the Associate Administrator: woven plastic bags, plastic film bags, textile bags, paper bags, IBCs and bulk packagings. Thickness of stainless steel for tank shell and heads for cargo tanks and portable tanks must be the greater of 7.62 mm (0.300 inch) or the thickness required for a tank with a design pressure at least equal to 1.5 times the vapor pressure of the lading at 46 C (115 F). The guns are packaged in accordance with Packing Method US 1 as specified in 173.62 of this subchapter.